I get it, but speaking as someone who used to design kitchen layouts for a living: Don’t put your sink in the corner. Just don’t.
Also, this has one major “feature” above and beyond the usual diagonal sink in a corner cabinet, in that you can swivel the faucet into the middle position and dispense water directly onto your floor. Genius!
That’d be awesome for me. I’m always giving my kids hot baths in a little tub out in the backyard. They love it but I have to haul the water out there.
My ex has the regular sink diagonally in the corner- and she’s too short. It has to be farther back from the edge of the counter to miss the corner. However she’s 5’2” (and overweight) so it’s harder to reach, enough to be an annoyance every time she washes dishes.
Just don’t put your sink in the corner. There is no good solution
No. Look at it in the picture. The gooseneck in it comes forward quite long enough to at the very least hit the countertop in the middle of the corner, and most of that water will either spill onto the floor if it doesn’t hit it directly.
Yeah this seems like something you would do if the space didn’t permit anything else. Which is the case sometimes. But it’s not something to elect when you have other options.
Ok, I’m super curious.
By “In the corner” do you mean putting a sink on the actual corner unit? Or by the tablespace immediately next to it?
In the case of the first one I totally get it. The corner unit is a cursed part of the kitchen anyway. If you mean immediately next to it, why not? Not disagreeing, just curious what a professional says.
The “correct” way, or most correct way I guess, is to have a cabinet in the corner that is diagonal, at 45 degrees relative to the left and right cabinet runs. Example:
You can buy premade angle cabinets that are designed for this, or you can just set a normal sink base cabinet at 45 degrees and mess around with fillers and so forth to space it out from the other two runs and hopefully ensure that there is sufficient clearance to open the doors and drawers on both it and the cabinets left and right of it. The disadvantage of this is it limits you to a surprisingly narrow sink, since it can’t be much if any wider than the face of the cabinet. And if you make the cabinet wider, you also have to bring it out into the room more and more as well, encroaching on your floor space. Normally people want to use a corner sink because they’re short on square footage anyway, so this is not ideal. Also, you inevitably wind up with a huge dead space behind the sink (that’s hard to reach, because there’s a sink and faucet in the way) and the further you bring out the face of the sink base cabinet the worse this gets.
The other way is to just have a dead or blind corner with a typical 90 degree transition in it, and just plonk the sink diagonally in the dead space. Example:
(This isn’t actually quite that as installed in a kitchen, but my low effort Google search did not turn up a great picture of this.) This has all the width limitation problems as the strategy above, but also forces you to stand in this stupid pie-wedge space with a hard corner in it, with the countertop edge digging into and the cabinet knobs hooking your belt loops all the time. It’s super annoying. In order to get a decently sized sink in here people often wind up pushing it back, and you’ll learn quickly that working in a sink that’s super far away is also really fuckin’ annoying.
Plan C which is now becoming popular is what OP posted, a double sink that’s got the 90 degree corner built into it. This is the worst of both worlds, if you ask me, because you still have to stand in a pie wedge plus the sink(s) you get are super narrow, and your functional setup becomes fraught with additional peril because idiots and/or children can activate the faucet with it aimed at neither sink, soaking your countertop, cabinets, and floor.
That makes a lot of sense. I was trying to work out why a sink immediately next to a corner was bad, but now I know what you mean.
I guess it’s a bad solution to trying to work around the problem of kitchen real estate, the same way trying to use for cabinet in the corner unit for anything is almost always a bad time.
The main reason it’s a bad idea is that 99% of the time the corner is where the seam is for the laminate skin, which is the weakest point in the counter and most likely to form gaps in the counter that water can get into and start to rot the plywood below. If you have granite I guess it would be less of a concern but I’m not familiar with the layout of those counters.
That does tend to happen. Even without swiveling the faucet, moving dishes between basins causes a bit of a puddle to develop. Thankfully I have a tiled floor so it doesn’t matter too much.
If someone is forced to use a tool in a manner that it wasn’t designed to be used in and a mistake happens, that’s neither the designer’s or user’s direct fault; it is the implementor’s fault.
You can be as careful and attentive as you can muster but that doesn’t change the fact that contrary design solutions were implemented and have rendered the use of the tool (the sink) both non-ergonomic and unintuitive. This will lead to accidents.
Yep, and they are actually awesome! I personally hate washing dishes when there’s a pile of them in front of you because of all the splashing. This layout makes cleaning so much easier. Additionally, you can put up some stuff for defrosting in the second sink
Could you just not put it there? I never known any sink in existence that is plumbed into the corner of the room, so presumably the piping has been redirected so that you need a corner sink, it’s literally the very definition of a solution looking for a problem and indeed a problem has to be created so the solution is required.
They are meant to be installed in a corner.
I get it, but speaking as someone who used to design kitchen layouts for a living: Don’t put your sink in the corner. Just don’t.
Also, this has one major “feature” above and beyond the usual diagonal sink in a corner cabinet, in that you can swivel the faucet into the middle position and dispense water directly onto your floor. Genius!
Or directly into a bucket.
How often I’m filling buckets vs. how often I’d accidentally spill water on the floor.
Would be a bad idea for me
FB12
Plastic floor bucket to sit on your floor.
$679
Ah. I see you found the “accessories” appendix of the KraftMaid catalog.
That’d be awesome for me. I’m always giving my kids hot baths in a little tub out in the backyard. They love it but I have to haul the water out there.
There are two things you never put in a corner: sinks and Baby.
The floor thing is awesome. You can easily fill a big barrel without a hose.
Just get a faucet with a hose. Helps with cleaning/rinsing dishes, too, especially if it has a good high pressure setting.
I was joking… Although maybe some people took it seriously.
I mean I guess in case of emergency as in I do not want to go to the store for a hose just for this one time thing…
My ex has the regular sink diagonally in the corner- and she’s too short. It has to be farther back from the edge of the counter to miss the corner. However she’s 5’2” (and overweight) so it’s harder to reach, enough to be an annoyance every time she washes dishes.
Just don’t put your sink in the corner. There is no good solution
So what I’m hearing is that the corner sink causes divorces.
Doesn’t the faucet travel over the corners so it wouldn’t spill on the floor (much anyways) without pulling the faucet out?
No. Look at it in the picture. The gooseneck in it comes forward quite long enough to at the very least hit the countertop in the middle of the corner, and most of that water will either spill onto the floor if it doesn’t hit it directly.
Yeah this seems like something you would do if the space didn’t permit anything else. Which is the case sometimes. But it’s not something to elect when you have other options.
Ok, I’m super curious. By “In the corner” do you mean putting a sink on the actual corner unit? Or by the tablespace immediately next to it?
In the case of the first one I totally get it. The corner unit is a cursed part of the kitchen anyway. If you mean immediately next to it, why not? Not disagreeing, just curious what a professional says.
There are a couple of ways people do this.
The “correct” way, or most correct way I guess, is to have a cabinet in the corner that is diagonal, at 45 degrees relative to the left and right cabinet runs. Example:
You can buy premade angle cabinets that are designed for this, or you can just set a normal sink base cabinet at 45 degrees and mess around with fillers and so forth to space it out from the other two runs and hopefully ensure that there is sufficient clearance to open the doors and drawers on both it and the cabinets left and right of it. The disadvantage of this is it limits you to a surprisingly narrow sink, since it can’t be much if any wider than the face of the cabinet. And if you make the cabinet wider, you also have to bring it out into the room more and more as well, encroaching on your floor space. Normally people want to use a corner sink because they’re short on square footage anyway, so this is not ideal. Also, you inevitably wind up with a huge dead space behind the sink (that’s hard to reach, because there’s a sink and faucet in the way) and the further you bring out the face of the sink base cabinet the worse this gets.
The other way is to just have a dead or blind corner with a typical 90 degree transition in it, and just plonk the sink diagonally in the dead space. Example:
(This isn’t actually quite that as installed in a kitchen, but my low effort Google search did not turn up a great picture of this.) This has all the width limitation problems as the strategy above, but also forces you to stand in this stupid pie-wedge space with a hard corner in it, with the countertop edge digging into and the cabinet knobs hooking your belt loops all the time. It’s super annoying. In order to get a decently sized sink in here people often wind up pushing it back, and you’ll learn quickly that working in a sink that’s super far away is also really fuckin’ annoying.
Plan C which is now becoming popular is what OP posted, a double sink that’s got the 90 degree corner built into it. This is the worst of both worlds, if you ask me, because you still have to stand in a pie wedge plus the sink(s) you get are super narrow, and your functional setup becomes fraught with additional peril because idiots and/or children can activate the faucet with it aimed at neither sink, soaking your countertop, cabinets, and floor.
Wow, thanks for the reply!
That makes a lot of sense. I was trying to work out why a sink immediately next to a corner was bad, but now I know what you mean.
I guess it’s a bad solution to trying to work around the problem of kitchen real estate, the same way trying to use for cabinet in the corner unit for anything is almost always a bad time.
The main reason it’s a bad idea is that 99% of the time the corner is where the seam is for the laminate skin, which is the weakest point in the counter and most likely to form gaps in the counter that water can get into and start to rot the plywood below. If you have granite I guess it would be less of a concern but I’m not familiar with the layout of those counters.
That does tend to happen. Even without swiveling the faucet, moving dishes between basins causes a bit of a puddle to develop. Thankfully I have a tiled floor so it doesn’t matter too much.
Perfect for when you need to mop the kitchen floor-- no bucket required /j
deleted by creator
Go back to your basement since you obviously have never done any chores that include using the kitchen sink
deleted by creator
No, it’s a poor
applicationimplementation of a design not intended for that application.deleted by creator
If someone is forced to use a tool in a manner that it wasn’t designed to be used in and a mistake happens, that’s neither the designer’s or user’s direct fault; it is the implementor’s fault.
You can be as careful and attentive as you can muster but that doesn’t change the fact that contrary design solutions were implemented and have rendered the use of the tool (the sink) both non-ergonomic and unintuitive. This will lead to accidents.
Words typed by someone who has never had to manage a child or teenager.
This makes so much more sense. Still wouldn’t want it, but I get it.
Yep, and they are actually awesome! I personally hate washing dishes when there’s a pile of them in front of you because of all the splashing. This layout makes cleaning so much easier. Additionally, you can put up some stuff for defrosting in the second sink
Finally, was wondering where exactly these things would have been used 😮
Yes, but that particular sink happens to be named “Baby”.
Could you just not put it there? I never known any sink in existence that is plumbed into the corner of the room, so presumably the piping has been redirected so that you need a corner sink, it’s literally the very definition of a solution looking for a problem and indeed a problem has to be created so the solution is required.
Still not centered.
Probably thinking of bars applications too.
deleted by creator
Or just a cramped dive bar, that and a troth.
…trough
#oddlysatisfying
deleted by creator